Protocols and Activities

The following table shows the protocols and activities supported by MetaDefender Industrial Firewall & IPS.

BACnet

Read Only

  • bvlc_result

  • read broadcast distribution table

  • read broadcast distribution table ack

  • read_foreign_device_table

  • read foreign device table ack

  • For forwarded npdu, distribute broadcast to network, and original unicast npdu and original broadcast npdu (for original broadcast npdu, the following is if a network SDU is NOT conveyed):

    • acknowledgeAlarm

    • confirmedCOVNotification

    • confirmedEventNotification

    • getAlarmSummary

    • getEnrollmentSummary

    • atomicReadFile

    • readProperty

    • readPropertyConditional

    • readPropertyMultiple

    • requestKey

    • readRange

    • lifeSafetyOperation

    • subscribeCOVProperty

    • getEventInformation

    • i-Am

    • i-Have

    • unconfirmedCOVNotification

    • unconfirmedEventNotification

    • timeSynchronization

    • who-Has

    • who-Is

    • utcTimeSynchronization

  • original broadcast npdu if a network SDU is conveyed:

    • Who-Is-Router-To-Network

    • Available for vendor proprietary messages

    • Reserved for use by ASHRAE

    • Network-Number-Is

    • What-Is-Network-Number

    • Set-Master-Key

    • Request-Master-Key

    • Update-Distribution-Key

    • Update-Key-Set

    • Request-Key-Update

    • Security-Response

    • Security-Payload

    • Challenge-Request

    • Disconnect-Connection-To-Network

    • Establish-Connection-To-Network

    • Initialize-Routing-Table-Ack

    • Initialize-Routing-Table

    • Router-Available-To-Network

    • Router-Busy-To-Network

    • Reject-Message-To-Network

    • I-Could-Be-Router-To-Network

    • I-Am-Router-To-Network

Read/Write

  • All Read Only operations

  • For forwarded npdu, distribute broadcast to network, original unicast npdu, and original broadcast npdu:

    • atomicReadFile

    • writeGroup

    • subscribeCOVProperty

    • writePropertyMultiple

    • writeProperty

    • deleteObject

    • createObject

    • removeListElement

    • addListElement

Full Access

  • Unrestricted access

BN3500

Read Only

  • Serial:

    • Read:

      • Rack Config

      • Slot Config

      • Group

      • Date & Time

      • Channel Setpoints

      • Rack Status

      • Rack Static Data

      • Channel Static Data

      • Alarm Event Recorder

      • System Event Recorder

      • Low Level Slot Config

      • Internal Calibration Parameter

      • Passwords

      • Request Rack Id

      • Reset Cfg/Sp Changed

      • Request/Release/Override Config Token

      • Write Date & Time

    • Download DSP Code

    • Config Announce

    • Config Announce 91

  • TDI:

    • Read:

      • TDI Configuration

      • Fixed FW Configuration

      • HW/FW Image

      • Low Level Configuration

      • Management DSP Code:

      • Speed DSP Code

      • Speed Test Code

      • Management Test Code

      • Management Code 0/1/2/3

      • Password

      • Status Data

      • Debug List

      • Historical Static/Waveform Data

      • High-Resolution Waveform Data

      • Current Waveform Data

      • All Current Static Data

      • Current Static Data

    • Write:

      • Fixed FW Configuration

      • Time

    • Acknowledge

  • Test:

    • Read Data Request

Read/Write

  • All Read Only operations

  • Serial:

    • Write Slot Config

    • Write Group

    • Write Time

    • Trip Multiply Group Enable/Disable

    • Rack Alarm Inhibit Enable/Disable

    • Set Software Switch

    • Write Channel Setpoints

    • Group Reset

    • Change Password (Config/Comm)

    • Clear Alarm/System Event Flag

    • Test Input Enable/Disable

    • Write Low Level Slot Config

    • Calibrate Channel

    • Device Reboot

    • IP Config

    • Auto Disconnect

  • TDI Write:

    • TDI Configuration

    • Low Level Configuration

    • Speed Test Code

    • Management Test Code

    • Management Code 0/1/2/3

    • Speed Code

    • Password

    • Set Transient Mode

    • Development/Debug:

    • Forced Transient Collection

    • Initiate Event

    • Clear Data

    • Enable/Disable Collection Group

  • Test:

    • Write Data Request

    • Execute Subroutine Request

    • Enter Test Mode Request

Full Access

  • Unrestricted access

DCERPC_PN_IO

Read Only

  • Read

  • Read Implicit

Read/Write

  • All Read Only operations

  • Connect

  • Release

  • Read

  • Write

  • Control

  • Read Implicit

Full Access

  • Unrestricted access

DNP3

Read Only

  • Confirmation

  • Read

  • Select

  • Open file

  • Close file

  • Get file information

  • Response

  • Unsolicited response

Read/Write

  • All Read Only operations

  • Write

  • Enable spontaneous messages

  • Disable spontaneous messages

  • Delete file

Full Access

  • Unrestricted access

DICOM

Read Only

  • STORE_RQ:

    • Not SCU to SCP transferring

  • N-ACTION-RQ:

    • Basic Film Session SOP Class:

      • Print Basic Film Session

    • Basic Film Box SOP Class:

      • Print Basic Film Box

  • C-GET-RQ

  • C-GET-RP

  • C-FIND-RQ

  • C-FIND-RP

  • C-ECHO-RQ

  • N-EVENT-REPORT-RQ

  • C-ECHO-RP

  • N-EVENT-REPORT-RP

  • N-GET-RQ

  • N-GET-RS

  • N-ACTION-RP

  • C-MOVE-RP

  • N-SET-RP

  • N-CREATE-RP

  • N_DELETE_RP

  • C-STORE_RP

  • SOP Class:

    • Basic Film Session SOP Class

    • Basic Film Box SOP Class

Read/Write

  • All Read Only operations

  • C-MOVE-RQ

  • N-SET-RQ

  • N-CREATE-RQ

  • N-DELETE-RQ

  • STORE_RQ:

    • SCU to SCP transferring

  • N-ACTION-RQ:

    • Procedural Event Logging SOP Class:

      • Record Procedural Event

    • Substance Administration Logging SOP Class:

      • Record Substance Administration Event

    • Media Creation Management SOP Class:

      • Initiate Media Creation

    • Unified Procedure Step - Pull SOP Class:

      • Change UPS State

  • N-ACTION-RQ:

    • Media Creation Management SOP Class:

      • Cancel Media Creation

    • Unified Procedure Step - Push SOP Class:

      • Request UPS Cancel

  • SOP Class:

    • Procedural Event Logging SOP Class

      • Substance Administration Logging SOP Class

      • Media Creation Management SOP Class

      • Unified Procedure Step - Pull SOP Class

      • Unified Procedure Step - Push SOP Class

Full Access

  • Unrestricted access

EGD

Read Only

  • Capabilities Request

  • Capabilities Response

  • NAK

  • Read Request

  • Read Response

  • Retrieve Configuration Request

  • Retrieve Configuration Response

  • Statistics Request

  • Statistics Response

  • Summary Request

  • Summary Response

Read/Write

  • All Read Only operations

  • Masked Write Request

  • Masked Write Response

  • Producer Consumer Exchange

  • Write Request

  • Write Response

Full Access

  • Unrestricted access

EtherCAT

Read

  • No Operation

  • Auto Increment Read

  • Configured Address Read

  • Broadcast Read

  • Logical Memory Read

Read/Write

  • All Read Only operations

  • Auto Increment Write

  • Auto Increment Read Write

  • Configured Address Write

  • Configured Address Read Write

  • Broadcast Write

  • Broadcast Read Write

  • Logical Memory Write

  • Logical Memory Read Write

  • Auto Increment Read Multiple Write

  • Configured Read Multiple Write

Full Access

  • Unrestricted access

Ethernet IP

Read Only

  • Get Attribute All

  • Set Attribute All

  • Get Attribute List

  • Reset

  • Start

  • Stop

  • Multiple Service Packet

  • Apply Attributes

  • Get Attribute Single

  • Find Next Object Instance

  • Error Response

  • Restore

  • Save

  • Get Member

  • Set Member

  • Insert Member

  • Remove Member

  • Group Sync

  • Unconnected Send

  • Forward Open

  • Get Connection Data

  • Search Connection Data

  • Ex Forward Open

  • Get Connection Owner

  • Large Forward Open

  • Reserved (CIP service code in {0, 11, 15, 18, 19}).

  • Reserved for additional Common Services (CIP service code in the range [29, 49]).

Read Only PCCC

  • Protected Type File Read

  • Protected Typed Logical Read with Two Address Fields

  • Word Range Read

  • Protected Typed Logical Read with Three Address Fields

  • Read Bytes Physical

  • Read Diagnostic Counters

  • Read Link Parameters

  • Read Section Size

  • Typed Read

  • Unprotected Read

  • Upload All Request

  • Upload Completed

  • Upload

  • Close File

  • Diagnostic Status

  • Echo

  • Enter Upload Mode

  • Exit Download/Upload Mode

  • File Read

  • Open File

  • Physical Read

Read/Write

  • All Read Only operations

  • Write Tag Fragmented Service

  • Write Tag Service

  • Write Object/Dint Service (Edit Timer Is Here Too)

  • Write Bit Service

Read/Write PCCC

  • Unprotected Bit Write

  • Read-Modify-Write

  • Protected Typed Logical Write with Mask

  • Bit Write Protected Typed Logical Write with Two Address Fields

  • File Write, Set Timeout

  • Set Data Table Size

  • Set Variables

  • Read-Modify-Write N

  • Word Range Write

  • Protected Typed File Write

  • Write Bytes Physical

  • Protected Typed Logical Write with Three Address Fields

  • Set NAKs

  • Physical Write

  • Unprotected Write

  • Typed Write

  • Protected Write

  • Protected Bit Write

  • Set ENQs

  • Set Link Parameters

  • Write Range Read

Full Access

  • All Read/Write Commands

  • Set Attribute Single

  • Set Attribute List

  • Create

  • Delete

  • Edit Controller Properties

  • PCCC Execution

  • SFC Forcing Enable 00

  • I/O Forcing Enable 00

  • SFC Forcing Disable 00

  • I/O Forcing Disable 00

FINS

Read Only

  • Broadcast test result

  • Clock

  • Controller data mode

  • Controller data status

  • Cycle time

  • Data link status

  • Data link table

  • Errors log

  • FAL/FALS messages

  • File parameters and content of files stored in the device

  • Memory areas

  • Network status

  • Parameter area

  • Program area

Read/Write

  • All Read Only operations

  • Clock

  • Controller data status

  • Controller data mode

  • Cycle time

  • Data link status

  • Data link table

  • Errors log

  • FAL/FALS messages

  • File parameters and content of files stored in the device

  • File transfer and reading broadcast test result

  • Memory areas

  • Network status

  • Parameter area

  • Program area

Full Access

  • Unrestricted access

MMS

Read Only

  • Status

  • Get Name List

  • Identify

  • Read

  • Get Variable Access Attributes

  • Get Scattered Access Attributes

  • Get Named Variable List Attributes

  • Get Named Type Attributes

  • Input

  • Report Semaphore Status

  • Report Pool Semaphore Status

  • Report Semaphore Entry Status

  • Initiate Upload Sequence

  • Upload Segment

  • Terminate Upload Sequence

  • Request Domain Upload

  • Get Domain Attributes

  • Get Program Invocation Attributes

  • Get Event Condition Attributes

  • Report Event Condition Status

  • Get Event Action Attributes

  • Report Event Action Status

  • Report Event Enrollment Status

  • Get Event Enrollment Attributes

  • Acknowledge Event Notification

  • Get Alarm Summary

  • Get Alarm Enrollment Summary

  • Read Journal

  • Report Journal Status

  • Get Capability List

  • File Open

  • File Read

  • File Close

  • File Directory

  • Select (Additional Service)

  • Alter Program Invocation Attributes (Additional Service)

  • Unit Control Load Segment (Additional Service)

  • Unit Control Upload (Additional Service)

  • Get Unit Control Attributes (Additional Service)

  • Get Event Condition List Attributes (Additional Service)

  • Report Event Condition List Status (Additional Service)

  • Get Data Exchange Attributes

  • Get Access Control List Attributes

  • Report Access Controlled Objects

Read/Write

  • All read-only operations

  • Rename

  • Write

  • Define Named Variable

  • Define Scattered Access

  • Delete Variable Access

  • Define Named Variable List

  • Delete Named Variable List

  • Define Named Type

  • Delete Named Type

  • Output

  • Define Semaphore

  • Delete Semaphore

  • Initiate Download Sequence

  • Download Segment

  • Terminate Download Sequence

  • Request Domain Download

  • Load Domain Content

  • Store Domain Content

  • Delete Domain

  • Create Program Invocation

  • Delete Program Invocation

  • Obtain File

  • Define Event Condition

  • Delete Event Condition

  • Alert Event Condition Monitoring

  • Define Event Action

  • Delete Event Action

  • Define Event Enrollment

  • Delete Event Enrollment

  • Alter Event Enrollment

  • Write Journal

  • Initialize Journal

  • Delete Journal

  • Create Journal

  • File Rename

  • File Delete

  • Define Access Control List

  • Delete Access Control List

  • Change Access Control List

  • Initiate Unit Control Load (Additional Service)

  • Create Unit Control (Additional Service)

  • Remove From Unit Control (Additional Service)

  • Add To Unit Control (Additional Service)

  • Load Unit Control From File (Additional Service)

  • Store Unit Control To File (Additional Service)

  • Delete Unit Control (Additional Service)

  • Define Event Condition List (Additional Service)

  • Delete Event Condition List (Additional Service)

  • Add Event Condition List Reference (Additional Service)

  • Remove Event Condition List Reference (Additional Service)

  • Alter Event Condition List Monitoring (Additional Service)

Full Access

  • Unrestricted access

MQTT

Read Only

  • PUBLISH0 = 0x30

  • PUBLISH 1 = 0x31

  • PUBLISH2 = 0x32

  • PUBLISH 3 = 0x33

  • PUBLISH4 = 0x34

  • PUBLISH 5 = 0x35

  • PUBLISH6 = 0x36

  • PUBLISH 7 = 0x37

  • PUBLISH8 = 0x38

  • PUBLISH 9 = 0x39

  • PUBLISHA = 0x3A

  • PUBLISH B = 0x3B

  • PUBLISHC = 0x3C

  • PUBLISH D = 0x3D

  • PUBLISHE = 0x3E

  • PUBLISH F = 0x3F

  • PUBACK = 0x40

  • PUBREC = 0x50

  • PUBREL = 0x62

  • PUBCOMP = 0x70

  • PINGREQ = 0xC0

  • PINGRESP = 0xD0

Read/Write

  • All read-only operations

  • CONNECT = 0x10

  • CONNACK = 0x20

  • SUBSCRIBE = 0x82

  • SUBACK = 0x90

  • UNSUBSCRIBE = 0xA2

  • UNSUBACK = 0xB0

  • DISCONNECT = 0xE0

  • AUTH = 0xF0

Full Access

  • All Read/Write operations

  • unknow1 = 0xc

  • unknow2 = 0xd2

OPC Classic

OPC-A&E

  • IOPCEventServer

  • IOPCEventServer2

  • IOPCEventAreaBrowser

  • IOPCEventSubscriptionMgt

  • IOPCEventSubscriptionMgt2

  • IOPCEventSink

OPC-DA

  • IOPCCommon

  • IOPCServer

  • IOPCBrowser

  • IOPCItemIO

  • IOPCItemMgt

  • IOPCGroupStateMgt

  • IOPCGroupStateMgt2

  • IOPCSyncIO

  • IOPCSyncIO2

  • IOPCAsyncIO2

  • IOPCAsyncIO3

  • IOPCItemDeadbandMgt

  • IOPCItemSamplingMgt

  • IOPCServerPublicGroups

  • IOPCBrowseServerAddressSpace

  • IOPCPublicGroupStateMgt

  • IOPCAsyncIO

  • IEnumOPCItemAttributes

  • IOPCDataCallback

  • IOPCItemProperties

OPC-HDA

  • IOPCHDA_Server

  • IOPCHDA_Browser

  • IOPCHDA_SyncRead

  • IOPCHDA_SyncUpdate

  • IOPCHDA_SyncAnnotations

  • IOPCHDA_AsyncRead

  • IOPCHDA_AsyncUpdate

  • IOPCHDA_AsyncAnnotations

  • IOPCHDA_Playback

  • IOPCHDA_DataCallback

OPC UA

Read Only

  • OPEN

  • MESSAGE

    • FindServersRequest

    • FindServersResponse

    • FindServersOnNetworkRequest

    • FindServersOnNetworkResponse

    • GetEndpointsRequest

    • GetEndpointsResponse

    • ReadRequest

    • ReadResponse

    • HistoryReadRequest

    • HistoryReadResponse

  • CLOSE

  • HELLO

  • ACKNOWLEDGE

  • ERROR

Read/Write

  • All read-only operations

  • MESSAGE

    • ServiceFault

    • RegisterServerRequest

    • RegisterServerResponse

    • RegisterServer2Request

    • RegisterServer2Response

    • OpenSecureChannelRequest

    • OpenSecureChannelResponse

    • CloseSecureChannelRequest

    • CloseSecureChannelResponse

    • CreateSessionRequest

    • CreateSessionResponse

    • ActivateSessionRequest

    • ActivateSessionResponse

    • CloseSessionRequest

    • CloseSessionResponse

    • CancelRequest

    • CancelResponse

    • AddNodesRequest

    • AddNodesResponse

    • AddReferencesRequest

    • AddReferencesResponse

    • DeleteNodesRequest

    • DeleteNodesResponse

    • DeleteReferencesRequest

    • DeleteReferencesResponse

    • BrowseRequest

    • BrowseResponse

    • BrowseNextRequest

    • BrowseNextResponse

    • TranslateBrowsePathsToNodeIdsRequest

    • TranslateBrowsePathsToNodeIdsResponse

    • RegisterNodesRequest

    • RegisterNodesResponse

    • UnregisterNodesRequest

    • UnregisterNodesResponse

    • QueryFirstRequest

    • QueryFirstResponse

    • QueryNextRequest

    • QueryNextResponse

    • ReadRequest

    • ReadResponse

    • HistoryReadRequest

    • HistoryReadResponse

    • WriteRequest

    • WriteResponse

    • HistoryUpdateRequest

    • HistoryUpdateResponse

    • CallRequest

    • CallResponse

    • CreateMonitoredItemsRequest

    • CreateMonitoredItemsResponse

    • ModifyMonitoredItemsRequest

    • ModifyMonitoredItemsResponse

    • SetMonitoringModeRequest

    • MonitoringModeResponse

    • SetTriggeringRequest

    • SetTriggeringResponse

    • DeleteMonitoredItemsRequest

    • DeleteMonitoredItemsResponse

    • CreateSubscriptionRequest

    • CreateSubscriptionResponse

    • ModifySubscriptionRequest

    • ModifySubscriptionResponse

    • SetPublishingModeRequest

    • OPC_UA_SetPublishingModeResponse

    • PublishRequest

    • PublishResponse

    • RepublishRequest

    • RepublishResponse

    • TransferSubscriptionsRequest

    • TransferSubscriptionsResponse

    • DeleteSubscriptionsRequest

    • DeleteSubscriptionsResponse

    • TestStackRequest

    • TestStackResponse

    • TestStackExRequest

    • TestStackExResponse

Full Access

  • Unrestricted access

GE-ADL

Read Only

  • Read Discrete Time

  • Read Discrete

  • Read Block

  • Ack

  • Read Symbol Addr

  • Read Mem Sizes

  • Read Fault History

  • Ping

  • Read Message Queue

  • Read Card ID

  • NAK

Read/Write

  • All read-only operations

  • Write Discrete

  • Write Block

Full Access

  • Unrestricted access

GE-SDI V6

Read Only

  • Request Is OK

  • Cannot Fork Child

  • Cannot Read Request

  • Cannot Write Reply

  • Invalid Request

  • Message Too Big

  • QNX Send Failed

  • Data Upload Failed

  • SMem Failed

  • Timed Out

  • Unknown Problem

  • No Proxy

  • No DLPA Net

  • No DLPA F0

  • Runtime Message

  • Bad ADII

  • Bad QNX QUE

  • No ISync Resp

  • Bad Open Cmd

  • File Open Failed

  • File Size Failed

  • Bye

  • Sys (Get ID CMD)

  • Sys (Get Var CMD)

  • Sys (Get Var Info CMD)

  • Sys (Get Idle CMD)

  • Sys (Get Obj CMD)

  • Sys (Sim Input CMD)

  • Sys (Sim Output CMD)

  • Sys (Get Forced PTS CMD)

  • Sys (Get Forced Vars CMD)

  • Sys (Get CBUF List CMD)

  • Sys (Get CBUF Status CMD)

  • Sys (Get CBUF Cfg CMD)

  • Sys (Get Rev CMD)

  • Sys (Get TMR CMD)

  • Sys (Get Totalizer CMD)

  • Sys (Get PCode Rev CMD)

  • Sys (Get MAC Addr CMD)

  • Sys (Get CBUF File CMD)

  • Sys (Get Signal Data CMD)

  • Splain

  • OC2K

  • Ack

  • Slow CMD

  • Progress Info

  • Ignoring RQST

  • Drive Open

  • Drive Send

  • Drive Resp

  • Disk Size

  • File Size

  • Read File

  • Dam NOOP CMD

  • Dam Halving Speed

  • Dam Pre-options CMD

  • Dam Var List Data

  • Dam Var List DOnly

  • Dam Var List SOnly

Read/Write

  • All Read Only operations

  • Sys (Put Var CMD)

  • Sys (Force Var CMD)

  • Sys (RMForce Var CMD)

  • Sys (RMForce All Var CMD)

  • Sys (Force Input CMD)

  • Sys (Force Output CMD)

  • Sys (RMSim PT CMD)

  • Sys (RMForce PT CMD)

  • Sys (RMForce All PTS CMD)

  • Sys (Put Obj CMD)

  • Sys (Upload CBUF CMD)

  • Sys (Set Time CMD)

  • Sys (Del Get Obj Context CMD)

  • Sys (Put EGD CMD)

  • Sys (Set Totalizer CMD)

  • Sys (Put EGD RMW CMD)

  • Sys (Cleanup DDR Context CMD)

  • Sys (Sav Sim CMD)

  • Sys (Restore Sim CMD)

  • WFile

  • RMFiles

  • Set Time

  • Del File

  • Dam Delete CMD

  • Dam Var List Add

  • Dam Var List Delete

Full Access

  • Unrestricted access

GE-SDI V6E

Read Only

  • Connect

  • Get ID

  • Get Var

  • Get Idle

  • Get Forced Vars

  • Get Rev

  • Bye

  • Get TMR

  • Get MAC Addr

  • Error

  • Get Totalizer

  • Ping

  • Get Log

  • Get Num Vars

  • Download Start

  • Download CMPLT

  • Get Load Log

  • Get App Rev

  • Disk Size

  • Read Cel Data

  • Read File

  • Authenticate

  • Get IO Module CRCS

  • Get Unidentified Modules

  • Get Profiler Config

  • Get Config State

  • Get EGD Diag

  • Get IO Pack Hostnames

  • Get EGD Diags Reset

  • Get IO Mode Lock State

  • Get Ctrl Lock State

  • Get Parameter REV

  • Get Unhealthy EGD Vars

  • Get DC

  • Get IO Module Masters

  • Get Supported Msgs

  • Get Conn Usage

  • Get ACFG Config

  • Get Config

  • Get Diag State

  • Get ACFG State

  • Get Flash Info

  • Get ACFG Cleanup State

  • Get FF Live List

  • Recv HSR

  • Get Module DHCP Requests

  • Read Card

  • Get FF LD Config

  • Get Security State

  • Get Last SCEP Error

  • Profi Connect

  • Profi Disconnect

  • Get App Rev2

  • Get Dev List

  • Get Rev2

  • OSM Request

  • RSG SDI Request

  • Get CBUF List

  • Get CBUF CFG

  • Get CBUF Status

  • Get DDR Rev

  • Get Sevdd History Queue

  • Get Sevdd Action Queue

  • Get Odd History Queue

  • Get Odd Active Queue

  • Dam NOOP CMD

  • Dam Var List Data

  • Dam EGD List Data

  • Dam Profiler List Add

  • Dam Profiler List Data

  • Dam EGD Health List Data

  • Alarm And Event Notification

  • Alarm Lock

  • Alarm Unlock

  • Alarm Acknowledge

  • Alarm Acknowledge All

  • Alarm Unacknowledge

  • Alarm Reset

  • Alarm Reset All

  • Alarm Silence

  • Alarm Silence All

  • Alarm Unsilence

  • Alarm Dump Process Queue

  • Alarm Ping

  • Alarm Acknowledge Hold

  • Alarm Acknowledge All Holds

  • Alarm Unacknowledge Hold

  • Alarm Reset Hold

  • Alarm Reset All Holds

  • Alarm Override Hold

  • Alarm Remove Hold Override

  • Alarm Dump Hold Queue

  • Alarm MSG Process Alarm

  • Alarm Msg Hold

  • Alarm MSG Event

  • Alarm MSG SOE

  • Alarm MSG Diagnostic

  • Alarm Not UDH Communicator

  • Alarm Process Queue Sync

  • Alarm Hold Queue Sync

  • Alarm And Event Notification Delete

  • Alarm Horn Silence

  • GE Alarm Dump Process Queue

  • GE Alarm Dump Hold Queue

  • GE Alarm MSG Process Alarm

  • Alarm Update SPLtoken Value

  • GE Alarm MSG Hold

  • Alarm MSG Diagnostic Queue Sync

  • Analog Alarm And Event Notification

  • User Alarm Lock

  • User Alarm Unlock

  • User Alarm Acknowledge

  • User Alarm Acknowledge All

  • User Alarm Unacknowledge

  • User Alarm Reset

  • User Alarm Reset All

  • User Alarm Silence

  • User Alarm Silence All

  • User Alarm Unsilence

  • Analog Alarm Dump Process Queue

  • User Alarm Acknowledge Hold

  • User Alarm Acknowledge All Holds

  • User Alarm Unacknowledge Hold

  • User Alarm Reset Hold

  • User Alarm Reset All Holds

  • User Alarm Remove Hold Override

  • User Alarm Override Hold

  • Analog Alarm MSG Process Alarm

  • Analog Alarm And Event Notification Delete

  • Analog MSG Process Alarm

  • V3 Alarm And Event Notification

  • V3 Alarm And Event Notification Delete

  • V3 Alarm MSG Process Alarm

  • V3 Alarm MSG Diagnostic Alarm

  • V3 Alarm Queues Sync

  • V3 Alarm Dump Queues

  • V3 Alarm Dump Process Alarm

  • V3 Alarm Transition FF Diagnostic

  • V3 Alarm Reset FF Diagnostic

  • V3 Alarm Dump FF Diagnostic

  • V3 Alarm Dump Configured FF Blocks With Active Alerts

  • V3 Alarm Command

  • V3 Global Alarm Command

  • V3_1 Alarm Process Alarm Register

  • V3_1_Alarm Process Alarm Unregister

  • V3_2_alarm Process Alarm Unregister

  • V3_2 Alarm Command

  • Workstation SDI

Read/Write

  • All Read Only operations

  • Put Var

  • Force Var

  • RMForce Var

  • RMForce All Vars

  • Exec System

  • Write File

  • Set Totalizer

  • Delete File

  • ADL Forward

  • Novram Save

  • Set Time

  • Add Redirection Route

  • Delete Redirection Route

  • Parameter Load Exec

  • Set User ID

  • Put Var With Name

  • Force Var With Name

  • RMForce Var With Name

  • Set DC

  • Dual load CMPLT

  • ACFG File Cleanup

  • ACFG Load Start

  • ACFG Load CMPLT

  • ACFG Load Exec

  • ACFG Release

  • Online Incremental Load Exec

  • Set ACFG Diag

  • Device Backup Load Exec

  • Send HSE

  • Set Security State

  • Profi Write

  • Upload CBUF

  • DDR Load Exec

  • Dam Var List Add

  • Dam Var List Delete

  • Dam IONet EGD List Add

  • Dam IONet EGD List Delete

  • Dam EGD List Add

  • Dam EGD List Delete

  • Dam Profiler List Delete

  • Dam EGD Health List Add

  • Dam EGD Health List Delete

  • Dam IONet EGD Health List Add

  • Dam IONet EGD Health List Delete

  • V3_1 Alarm Dump

  • V3_2 Alarm Process Alarm Register

Full Access

  • Unrestricted access

GE-SRTP

Read Only

  • PLC Short Status Request

  • PLC Long Status Request

  • Return Control Program Names

  • Read System Memory

  • Read Task Memory

  • Read Program Memory

  • Establish Datagram

  • Programmer Log On

  • Return PLC Time Data

  • Get Module Status

  • Return Fault Table

  • Return Control Information

  • Block Manage

  • Session Control

  • PLC Features Supported

  • Read Addr Var

  • Symbol Lookup

  • Get DSM File

  • Notification Registration

  • File Read

  • Dir

  • FChecksum

  • Target Logon

  • Poll For Response

  • Deliver Protocol

  • Remote Read Services

  • Get All PVT Locations

  • Get Default Priv Level

  • Get Priv Level Info

Read/Write

  • All read-only operations

  • Write System Memory

  • Write Task Memory

  • Write Program Block Memory

  • Update Datagram

  • Set Control CPU ID

  • Set PLC State

  • Set PLC Time Data

  • PLC Clear All

  • Clear Selected FLT

  • Clear Fault Table

  • Write Datagram

  • Write Addr Var

  • File Write

  • FDelete

  • Rename

  • FCopy

  • Reference Set

  • Remote Write Services

Full Access

  • Unrestricted access

IEC60870

Read Only

  • APCI Format: S type

  • APCI Format: U type:

    • Startdt

    • Testfr

  • APCI Format: I type:

    • Single point information

    • Step position information

    • Step position information with time tag

    • Bit string of 32 bit

    • Bit string of 32 bit with time tag

    • Measured value, normalized value

    • Measured value, normalized value with time tag

    • Measured value, scaled value

    • Measured value, scaled value with time tag

    • Measured value, short floating point value

    • Measured value, short floating point value with time tag

    • Integrated totals

    • Integrated totals with time tag

    • Event of protection equipment with time tag

    • Packed start events of protection equipment with time tag

    • Packed output circuit information of protection equipment with time tag

    • Packed single point information with status change detection

    • Single point information with time tag CP56Time2a

    • Measured value, normalized value without quality descriptor

    • Double point information with time tag CP56Time2a

    • Step position information with time tag CP56Time2a

    • Bit string of 32 bit with time tag CP56Time2a

    • Measured value, normalized value with time tag CP56Time2a

    • Measured value, scaled value with time tag CP56Time2a

    • Measured value, short floating point value with time tag CP56Time2a

    • Integrated totals with time tag CP56Time2a

    • Event of protection equipment with time tag CP56Time2a

    • Packed start events of protection equipment with time tag CP56Time2a

    • Packed output circuit information of protection equipment with time tag CP56Time2a

    • End of initialization

    • (General) Interrogation command

    • Counter interrogation command

    • Read command

    • Clock synchronization command

    • (IEC 101) Test command

    • (IEC 101) Delay acquisition command

    • Test command with time tag CP56Time2a

    • File ready

    • Section ready

    • Call directory, select file, call file, call section

    • Ack file, ack section

    • Directory

    • Query Log - Request archive file

    • Double point information with time tag

    • Double point information

    • Single point information with time tag

Read/Write

  • All read-only operations

  • APCI Format: I type:

    • Setpoint command, normalized value

    • Setpoint command, scaled value

    • Setpoint command, short floating-point value

    • Bit string 32 bit

    • Setpoint command, normalized value with time tag CP56Time2a

    • Setpoint command, scaled value with time tag CP56Time2a

    • Setpoint command, short floating point value with time tag CP56Time2a

    • Bit string 32 bit with time tag CP56Time2a

    • Parameter of measured value, normalized value

    • Parameter of measured value, scaled value

    • Parameter of measured value, short floating point value

    • Parameter activation

    • Last section, last segment

    • Segment

Full Access

  • Unrestricted access

iFix

Read Only

  • Variable Access:

    • Read Request

    • Read Response

    • Get Variable Definition Request

    • Get Variable Definition Response

    • Database Reload Request

    • Database Reload Response

    • Initiate DB Reload Request

    • Initiate DB Reload Response

    • Terminate DB Reload Request

    • Terminate DB Reload Response

  • Alarm Handling | Session-Oriented Alarm:

    • Alarm Message

    • Session Alarm Request

    • Session Alarm Response

  • Connection Manager:

    • Check Session Request

    • Check Session Response

    • Connection Management Request

    • Connection Management Response

    • Connection Info Data Request

    • Connection Info Data Response

    • Diagnostic Request

    • Diagnostic Response

    • Remote Node Is Shutting Down

  • Transfer Data:

    • Transfer Data Request

    • Transfer Data Response

  • Mdba Handshake:

    • Mdba Handshake Request

    • Mdba Handshake Response

Read/Write

  • All read-only operations

  • Variable Access:

    • Write Response

    • Write Request

Full Access

  • Unrestricted access

  • Variable Access:

Modbus

Read Only

  • Read Coils

  • Read Discrete Inputs

  • Read Holding Registers

  • Read Input Registers

  • Read Exception Status

  • Read Diagnostics

  • Read - Fetch Comm Event Ctr

  • Read - Fetch Comm Event Log

  • Read - Report Slave Id

  • Read File Record

  • Read/Write Multiple Registers

  • Read Fifo Queue

Read/Write

  • All read-only operations

  • Write Single Coil

  • Write Single Register

  • Write Multiple Coils

  • Write Multiple Registers

Read UMAS:

  • Unity

    • INIT COMM

    • Read Id

    • Read Project Info

    • Read Plc Info

    • Read Card Info

    • Request For Memory Read

    • Repeat

    • Take Plc Reservation

    • Release Plc Reservation

    • Keep Alive

    • Read Memory Block

    • Read Variable

    • Read Coils Registers

    • Initialize Download

    • Download Block

    • End Strategy Download

    • Read Eth Master Data

    • Monitor Plc

    • Data Information Request

    • Check Plc Status Connect Diag Buffer

    • Read Io Object

    • Read Io Module

    • Reading System Bits

    • Reading System Words

Write UMAS:

  • All read UMAS operations

  • Unity:

    • Write Memory Block

    • Write Variable

    • Write Coils Register

    • Write Io Object

    • Writing System Bits

    • Writing System Words

Full Access

  • Unrestricted access

PCCC

Read Only

  • close file

  • diagnostic status

  • echo

  • enter upload mode

  • exit download/upload mode

  • file read

  • open file

  • physical read

  • protected typed file read

  • protected typed logical read with two address fields

  • protected typed logical read with three address fields

  • read bytes physical

  • read diagnostic counters

  • read link parameters

  • read section size

  • typed read

  • unprotected read

  • upload all request

  • upload completed

  • upload word range read

Read/Write

  • All read-only operations

  • bit write

  • file write

  • physical write

  • protected bit write

  • protected typed file write

  • protected typed logical write with two address fields

  • protected typed logical write with three address fields

  • protected typed logical write with mask

  • protected write

  • read-modify-write

  • read-modify-write N

  • set data table size

  • set link parameters

  • set ENQs

  • set link parameters

  • set NAKs

  • set timeout

  • set variables

  • typed write

  • unprotected bit write

  • unprotected write

  • word range write

  • write bytes physical

Full Access

  • Unrestricted access

PNDCP

Read Only

  • Hello

  • Identify

  • Get PLC's information

Read/Write

  • All Read Only operations

  • Set PLC's Information

Full Access

  • Unrestricted access

S7

Read Only

  • Alarm query

  • CPU states

  • Clock

  • Diagnostic information

  • Variables

  • Get the program that was loaded in the PLC

Read/Write

  • All Read Only operations

  • Set the clock

  • Upload a program or firmware in the PLC (both use the same code)

  • Write variables

TIA Portal Read Only

  • All S7 Read Only operations

  • TIA Portal can establish a connection and read data from the PLC.

TIA Portal Read/Write

  • All S7 Read/Write operations EXCEPT does not allow firmware or program logic updates

  • TIA Portal can establish a connection and update/write values.

Full Access

  • Unrestricted access

SLMP

Read Only

  • Data of CPU module devices

  • Data of SLMP-compatible devices

  • Data using labels

  • Memory buffer of intelligent function module

  • Parameters and programs from CPU module and SLMP compatible devices

Read/Write

  • All Read Only operations

  • Data of CPU module devices

  • Data of SLMP-compatible devices

  • Data using labels

  • Memory buffer of intelligent function module

  • Parameters and programs from CPU module and SLMP compatible devices

Full Access

  • Unrestricted access


null
On This Page
Protocols and ActivitiesBACnetBN3500DCERPC_PN_IODNP3DICOMEGDEtherCATEthernet IPFINSMMSMQTTOPC ClassicOPC UAGE-ADLGE-SDI V6GE-SDI V6EGE-SRTPIEC60870iFixModbusPCCCPNDCPS7SLMPRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessReadRead/WriteFull AccessRead OnlyRead Only PCCCRead/WriteRead/Write PCCCFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessOPC-A&EOPC-DAOPC-HDARead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteRead UMAS:Write UMAS:Full AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteFull AccessRead OnlyRead/WriteTIA Portal Read OnlyTIA Portal Read/WriteFull AccessRead OnlyRead/WriteFull Access